Free Shipping logo FREE SHIPPING £75+
50 years of Telonic Instruments Ltd logo CELEBRATING 50+ YEARS
Price Match logo PRICE MATCH GUARANTEE

Archive for December, 2020

Record Mode on the MSO5000, DS7000 and MSO8000

You can use Pass/Fail measurements for a number of applications. With this scope family you can set it up to stop or continue when there is a failure, you can have the instrument make a beep or take a screen shot when a failure occurs.  You can create masks with varying error budgets around a target signal, and you can even use the record mode to record all the failures as frames. In this way, yo...

The MSO5000, DS7000 and MSO8000’s cursor capability

The MSO5000, DS7000 and MSO8000 can all use several different types of cursors to measure the signal.  These include manual, Track, XY and Measure.  Manual cursors allow you to set the X and Y relationship of the cursors to manually measure the signal.  Track cursors allow you to move in the X direction and the instrument keeps the cursor on the signal. XY cursors will be grayed out under norma...

How to create a reference on the MSO5000, DS7000 and MSO8000

A reference signal can be created and stored on the scope to compare against later on.  It can either be save and recalled later or shown on the display. To save a reference press "Ref" and then press "SaveToRef" this will save a reference of your signal and display it behind the signal.  If you would like to save multiple references you r will need to change the current reference from Ref1 to R...

Search and Navigation capability on the MSO5000, DS7000 and MSO8000

Search and Navigation is a great feature to easily move around on long complex signals with multiple trigger events.  The Search and Navigation feature can be used when either an edge, pulse, runt, slop, RS232, I2C or SPI signal is being trigger on and can allow you to select a desired trigger point.For this example I h...

Saving csv data on the DS/MSO1000Z series scopes

DS/MSO1000Z series scopes utilize USB for saving csv files to an external USB memory stick. 12 meg of csv data can be saved in approximately 30 minutes. Once an acquisition is made you can save the csv file using these steps:Press the Storage key on the keypad and then select CSV on the right side of the display. Select ...

Update Firmware on the MSO5000 & DS7000 Series Digital Oscilloscope

To update the firmware push the keypad Utility key followed by System at the bottom right corner of the display:...

How to use the MSO5000, DS7000 and MSO8000 Logic Analyzer different capabilities

The logic analyzer allows you to view up to 16 digital channels at once along with group them and label them to make your measurements easier to view. To activate the logic analyzer, press the “LA” button or the “L” section at the bottom of the display.  Note that the LA channels will allow you some vertical scaling control within the LA menu,...

Inverted color printing with the Rigol DS2000/A, DS4000, and DS6000 Oscilloscopes

The DS series of oscilloscopes can save display images directly to an external USB memory device using the Quick Print feature.This can be extremely helpful in documenting the input waveforms as well as the instrument settings and any measurements that may be active on the display. ...

DS1000Z Counter Technical Details

Basic specifications: - Counter sampling rate is fixed at 250 MSa/sec- Hysteresis level (defined further below) is ~1 division on the smallest vertical ranges (< 5 mV) and about 0.3 divisions (with Noise Reject Off) ir 0.7 divisions (with Noise Reject on) in higher vertical scal...

Direct waveform transfer from a DS1000Z scope to a DG4000 generator

...

MSO8000, DS7000 and the MSO5000 Arbitrary Waveform Generator

The signal generator allows you to both create standard waveforms but also allows you to easily create some custom waveforms as well as replicate a captured signal on the oscilloscope. To activate the logic analyzer, press either “GI” or “GII” on either the front panel of the instrument or at the bottom of the screen. To begin with ...

DS1000Z noise performance

Here are a few screen captures of a DS1104Z series oscilloscope with various inputs. The intent is to show the basic noise you can expect from a similar instrument. Figure 1: D...

Sub Categories

AC Power Supplies / Frequency Converters Offers & Promotions (1)

Application Notes

Blog (97)

DC Power Supplies Offers & Promotions (6)

Digital Multimeters Offers & Promotions (1)

Digital Oscilloscopes Offers & Promotions (5)

Electronic Loads Offers & Promotions (1)

Events (7)

Knowledge Base AC Power Supplies

Knowledge Base Data Acquisition Systems

Knowledge Base DC Power Supplies

Knowledge Base DG1000 Series (14)

Knowledge Base DG4000 Series (14)

Knowledge Base Digital Multimeters

Knowledge Base Digital Oscilloscopes

Knowledge Base DL3000 Series (2)

Knowledge Base DM3000 Series (21)

Knowledge Base DP700 Series (8)

Knowledge Base DP800 Series (26)

Knowledge Base DS1000 Series (46)

Knowledge Base DS2000 Series (36)

Knowledge Base DSA800 Series (70)

Knowledge Base DSG800 Series (2)

Knowledge Base Electrical Safety Analysers

Knowledge Base Electronic Loads

Knowledge Base M300 Series (2)

Knowledge Base MSO/DS7000 Series (35)

Knowledge Base MSO5000 Series (35)

Knowledge Base MSO8000 Series (32)

Knowledge Base PBZ Series (3)

Knowledge Base PCR-LE Series (3)

Knowledge Base PCR-MA Series (3)

Knowledge Base PCR-WE/WE2 Series (3)

Knowledge Base PLZ-5W Series (3)

Knowledge Base PLZ-5WH Series (3)

Knowledge Base PLZ-5WH2 Series (3)

Knowledge Base PMX-Multi Series (3)

Knowledge Base PWR-01 Series (3)

Knowledge Base RF Signal Generators

Knowledge Base RSA3000 Series (32)

Knowledge Base RSA5000 Series (31)

Knowledge Base SDG1000X Series (10)

Knowledge Base SDG2000X Series (11)

Knowledge Base SDG6000X Series (11)

Knowledge Base SDG800 Series (10)

Knowledge Base SDL1000X Series (5)

Knowledge Base SDM3000 Series (6)

Knowledge Base SDS1000X-E Series (15)

Knowledge Base SDS2000X-E Series (15)

Knowledge Base SDS5000X Series (15)

Knowledge Base SPD1000X (5)

Knowledge Base SPD3000X/X-E Series (6)

Knowledge Base Spectrum Analysers

Knowledge Base SSA3000X Plus Series (2)

Knowledge Base SSA3000X Series (15)

Knowledge Base SSA3000X-R Series (1)

Knowledge Base SSG3000X Series (4)

Knowledge Base SVA1000X Series (13)

Knowledge Base TOS9300 Series (3)

Knowledge Base Waveform Generators

LCR Meters Offers & Promotions (1)

Product Support (1)

RF Signal Generators (1)

Safety Testers Offers & Promotions (1)

Spectrum Analysers Offers & Promotions (4)

Telonic Instruments News (19)

Telonic Offers & Promotions (8)

CLICK TO CALL

0118 9786911
CLICK TO EMAIL