CONTACT ACCOUNT

TEL: 0118 978 6911

Home / Blog (Page 3)

Blog

End of Line Kikusui PWR400L DC Power Supply

Posted on: June 30th, 2021 by Doug Lovell

30/06/2021
To view the PWR400L product page please see HERE...

End of Line Kikusui PAS40-9 DC Power Supply

Posted on: June 30th, 2021 by Doug Lovell

30/06/2021
To view the PAS40-9 product page please see HERE...

End of Line Kikusui PWR1600H DC Power Supply

Posted on: June 30th, 2021 by Doug Lovell

30/06/2021
To view the PWR1600H product page please see HERE...

End of Line Kikusui PAN60-6A DC Power Supply

Posted on: June 30th, 2021 by Doug Lovell

30/06/2021
To view the PAN60-6A product page please see HERE...

DC Electronic Load – Part 4: How Each Operation Mode Works with Other Modes?

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
We have so far explained the four major operation modes for electronic loads - 1) constant current 2) constant resistance 3) constant voltage and 4) constant power, in the previous white papers. Now this paper describes how these modes relate to each other and how each mode works on other modes. 4-1. Relationship between Operation Modes Figure 4-1 shows the block diagram for the...

How to Double Output Voltage from Two PBZ through BTL* Connection

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
Here is an introduction on a method to achieve a double output voltage using two units of PBZ. The actual connection of PBZs is shown in Figure 1 as; -‘OUT’ terminals are used for output. - Only ‘COM’ terminal can be earthed for output, if required. Fo...

Useful Functions and Precautions for Using L-Load/C-Load in PCR-LE Series

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
1. When Using Inductive Load (L-Load)1-1 Soft Start A typical L-load is a motor load. E.g.) If using an induction motor load, the startup current can be 5 times (or more) larger than the normal startup current and it flows for several hundred ms. In this situation; 1) The motor load becomes inductive. 2) The power factor is approx. 0.5 at peak current. PCR-LE Series features...

Which Power Supply is Most Suitable to Run DC Motor?

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
When choosing a power supply to run a DC motor, the first and most important thing you need to consider is a maximum current that your motor will use. DC motor typically requires a startup current which is quite a lot higher than its running current. Due to this, not all DC power supplies can provide sufficient power to DC motors. In this white paper, we will take a look at the capability of our ...

How to Balance Battery Module Charge-Discharge

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
With the recent diversification of battery module application such as for automotive and backup, more and more users want to conduct a battery module charge-discharge test, besides of an individual cell battery test. As a battery management system has been greatly developed to maximize battery’s capacity, the practical needs to perform evaluations on balancing battery charge-discharge are incre...

DC Power Supply Sinks Current when Output is Turned Off

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
When using a DC power supply for charging a load such as battery or capacitor, it is important to note that the DC power supply absorbs a current from such loads when the output is turned off. Here we are going to further explain this power supply’s behaviour; DC power supply, in general, comprises a bleeder circuit to discharge a power supply’s electrolytic capacitor at its output terminal. I...

How to use the voltage correction function on frequency response

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
The PCR-WE can output up to 5 kHz, but it has frequency response as shown in the figure below. The response is about -3dB at 5kHz. For example, the waveform in the figure below is for 120 Vrms, 5 kHz. ...

DC Electronic Load – Part 1: What is a DC Electronic Load?

Posted on: June 23rd, 2021 by Doug Lovell

23/06/2021
Beginners who have never used an electronic load may well get confused with the difference between electronic loads and power supplies. They sometimes wonder ‘why the electronic load does not provide any output...?’ While similar in appearance, electronic loads are totally different from power supplies. It is not often you get to see them but it is suitable for specific applications such as w...

Sub Categories

Telonic Instruments News (17)

Telonic Offers & Promotions (5)

AC Power Supplies / Frequency Converters Offers & Promotions (1)

DC Power Supplies Offers & Promotions (6)

Electronic Loads Offers & Promotions (1)

LCR Meters Offers & Promotions (1)

Safety Testers Offers & Promotions (1)

Digital Multimeters Offers & Promotions (1)

Digital Oscilloscopes Offers & Promotions (5)

RF Signal Generators (1)

Spectrum Analysers Offers & Promotions (4)

Product Categories

AC Power Supplies / Frequency Converters
DC Power Supplies
DC Electronic Loads
Test & Measurement
Safety Testers
EMC
Soldering Irons / Test Tools
Manufacturers
Rental

Service & Support

About
Contact
Newsletter
Returns
Terms and Conditions
Privacy Policy
Shipping & Delivery
My account

Support, News & Events

Latest News
Future Events
Product Support
Blog

Copyright © 2024. All rights reserved by Telonic Instruments Ltd

Website operated by Jumping Giraffe Ltd. Jumping Giraffe Ltd is not responsible for content on external websites.