| Bandwidth limitation | 20MHz |
| Hardware Filtering | High pass (30KHz~ maximum bandwidth)
Low pass (maximum bandwidth ~30KHz) |
| Input coupling | DC、AC、GND |
| Input impedances | 1MΩ±1%||15pF±3pF |
| Vertical resolution | 8 bit |
| DC gain accuracy (Amplitude accuracy） | ＜±2%(1MΩ input ) |
| Vertical scale factor | 500uV/div~5V/div (1MΩ input, 500uV/div bandwidth 20MHz) |
| Channel-to-channel isolation DC to maximum bandwidth | ≥40dB（100:1） |
| Offset range | ± 2.5V (with probe multiple X1, <500mV/div), ±120V (with probe multiple X1, ≥500mV/div) |
| Noise | ≤1mV |
| Maximum input voltage | CAT I 300V(1MΩ input） |
| Horizontal System | |
|---|
| Time base range | 2ns/div~1ks/div |
| Time base delay range | -14divisions to 14ks |
| Clock drift | ≤±5ppm/year |
| Time base accuracy | ±20ppm |
| Roll mode | 200ms/div~1ks/div |
| Sampling System | |
|---|
| Sampling mode | Real time sample rate |
Peak sampling
Sample rate 1G Sa/s | All the sampling glitches in scanning rate are narrow to single channel 1 ns, dual channel 2 ns .four channel 4ns |
| Max duration in the max sampling rate | 1GSa/s: 28ms
500MSa/s: 56/28ms
250MSa/s: 56/28ms |
| Average | Average of sampling for N times
N is chosen from 2, 4, 8, 16, 32, 64, 128, 256 |
| Envelope | Envelope of sampling for N times
N is chosen from 2, 4, 8, 16, 32, 64, 128, 256, ∞ |
| Trigger System | |
|---|
| Trigger mode | Normal、Auto、and Single |
| Trigger coupling | DC、AC、HF reject(＞50KHz)、LF reject(＜50KHz)、noise reject |
| Trigger hold off range | 200ns~10s |
| Trigger level ranges | ±10 grids from the center of the screen |
| Trigger type | |
| Edge | Positive, negative, or either slope on any channel input. Coupling includes DC, AC, HF reject, LF reject, and noise reject. |
| Pulse Width | Trigger on width of positive or negative pulses that are＞,＜, ＝, ≠, or inside/outside a specified period of time (8ns~10s). |
| Logic | Trigger when any logical pattern of channels goes false or stays true for specified period of time (8ns~10s). Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for all input channels defined as High, Low, or Don’t Care |
| Nth Edge | Trigger on the Nth rising/falling edge of the waveform |
| Runt | By setting high and low thresholds, triggering pulses that span a level that does not cross another level captures positive and negative pulses |
| Slope | Trigger when the waveform’s time from one level to another matches the set time condition |
| Time Out | Starting from the intersection of the signal and the trigger level,Trigger when the trigger level is above (or below) the duration and reaches the set time |
| Video Trigger | The triggering method for video signals is different depending on the video format. Generally, there are PAL/625, SECAM, NTSC/525, 720P, 1080I, 1080P, etc. |
| Bus | Trigger for the set bus, including UART, I2C, SPI, CAN, LIN, 1553B, 429 bus UART: start bit, stop bit, data, 0: data, 1: data, x: data, parity error
I2C: Start condition, stop condition, acknowledge loss, restart, address field no acknowledgement, frame type 1, frame type 2, EEPROM data read and write, 10-bit write frame
SPI: CS, data, X data
CAN: frame start, remote frame ID, data frame ID, remote/data frame ID, data frame ID and data, error frame, all errors, acknowledgment errors, overload frames
LIN: Synchronous rising edge, frame ID, frame ID and data
1553B: instruction/status word sync header, data word sync header, instruction/status word, remote terminal address, Manchester code error, data word, odd parity error, all errors
429: word start, word end, LABEL, SDI, DATA, SSM, LABEL+SDI, Label+Data, Label+SSM, word error, word gap error, check error, all errors, all 0 bits, all 1 bit |
| General Specifications | |
|---|
| Power source voltage | 100~240V AC,50/60Hz |
| Power consumption | ＜60W |
| Fuse | 12V DC,5A |
| Built-in Battery | 7.4V, 7500mAh |
| Temperature | Operating: 0℃~45℃
Non-Operating: -40℃~60℃ |
| Humidity | Operating: 5%to 85%，25℃Non-Operating: 5% to 90%，25℃ |
| Altitude | Operating: ＜3000mNon-Operating: ＜12000m |
| Dimensions | 280mm*180mm*50mm |
| Weight | 2CH: 1340g, 4CH: 1425g |
Reviews
There are no reviews yet.