CONTACT
TEL: 0118 978 6911
Home / Knowledge Base (Page 15)

Knowledge Base

DSA Ethernet connectivity troubleshooting

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
Communicating over LAN to the DSA series is straightforward. Here are some things to try if you are having difficulty:1.    Make sure Ethernet cable is connected properly and that the switch/hubs in the network configuration are operating properly.o    The green LED on the bac...

How to enable the log frequency scale of the DSA815

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
Starting at firmware revision 00.01.12, the DSA815 spectrum analyser can display the frequency scale in Log mode. Press SPAN and set X Scale to Log ...

How do I save a user setup with a DSA800?

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
To save a setup: 1)    Insert USB stick into the USB port on the front panel  NOTE: The format of the USB stick must be FAT32  2)    Press STORAGE > Set BROWSER to DIR. You can press the butt...

How can I optimize the Peak scan measurements on a DSA spectrum analyser?

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
Spectrum analysers are extremely helpful tools for visualising signals in frequency space. This note will describe how to use settings to minimize error when performing peak measurements using a Rigol DSA Spectrum analyser.Radio Frequency signals, especially continuous wave (CW) signals, have a finite frequency width.  ...

Using Excel and VBA with DSA800 spectrum Analysers

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
Microsoft Excel and Visual Basic for Applications (VBA) is a great way for engineers who need to analyse and archive data from their instrument to access the data without deep programming skills.With this in mind, we have created VBA examples for some of our instruments including this one for Spectrum Analyzers including...

NRSC AM Measurements using a DSA

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
The Rigol DSA815 Spectrum Analyser has a built in Limit Line test that can be a convenient way to measure and compare spectral power against specific masks used for various signal types. One common test is NRSC Amplitude Modulation (AM) test. In this example, we are going to use the Pass/Fail mask to evaluate an AM Channel vs. limits set up by the National R...

How do I measure FM Deviation with a DSA?

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
General purpose spectrum analysers like the Rigol DSA series can be used to test the deviation of an FM signal. In this example, we are going to measure the FM deviation of a 10MHz FM signal with a DSA815. This is Rigol’s 1.5GHz spectrum analyser. NOTE: We are starting from Fact...

What is the fastest sweep time in Zero Span mode with a Spectrum Analyser?

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
The Rigol DSA815 Spectrum analyser features a zero span mode that can be helpful in observing modulated signals. In swept mode, the detector of the analyser is sweeping across a span of frequencies at a predefined rate. The display then shows the amplitude vs. frequency of that swept scan.  In zero span mode, the detect...

How to use UltraSigma to retrieve trace data from a DSA800

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
1.    Download and install UltraSigma software  2.    Physically connect instrument to LAN network and get IP address. You can check the IP address by pressing SYSTEM > IO SETTING > LAN  ...

How to Load an RSA3000 License Option

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
...

How to check the version of UltraSpectrum software

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
How to check the version of UltraSpectrum software Start UltraSigma software Select the spectrum analyser that you wish to control by left-clicking on the instrument ID string Right-click and select UltraSpectrum ...

Defective UltraSpectrum display with DSA800 series

Posted on: December 16th, 2020 by Doug Lovell
16/12/2020
If you experience a defective UltraSpectrum display while connected to a DSA800 series spectrum analyser the most likely cause is due to a UltraSpectrum software version mismatch. Software version  00.01.00.27 corrects the issue and can be downloaded from the blue Downloads tab at:...

Sub Categories

Application Notes

Knowledge Base AC Power Supplies

Knowledge Base PCR-LE Series (3)

Knowledge Base PCR-MA Series (3)

Knowledge Base PCR-WE/WE2 Series (3)

Knowledge Base Data Acquisition Systems

Knowledge Base M300 Series (2)

Knowledge Base DC Power Supplies

Knowledge Base DP700 Series (8)

Knowledge Base DP800 Series (26)

Knowledge Base PBZ Series (3)

Knowledge Base PMX-Multi Series (3)

Knowledge Base PWR-01 Series (3)

Knowledge Base SPD1000X (5)

Knowledge Base SPD3000X/X-E Series (6)

Knowledge Base Digital Multimeters

Knowledge Base DM3000 Series (21)

Knowledge Base SDM3000 Series (6)

Knowledge Base Digital Oscilloscopes

Knowledge Base DS1000 Series (46)

Knowledge Base DS2000 Series (36)

Knowledge Base MSO/DS7000 Series (35)

Knowledge Base MSO5000 Series (35)

Knowledge Base MSO8000 Series (32)

Knowledge Base SDS1000X-E Series (15)

Knowledge Base SDS2000X-E Series (15)

Knowledge Base SDS5000X Series (15)

Knowledge Base Electrical Safety Analysers

Knowledge Base TOS9300 Series (3)

Knowledge Base Electronic Loads

Knowledge Base DL3000 Series (2)

Knowledge Base PLZ-5W Series (3)

Knowledge Base PLZ-5WH Series (3)

Knowledge Base PLZ-5WH2 Series (3)

Knowledge Base SDL1000X Series (5)

Knowledge Base RF Signal Generators

Knowledge Base DSG800 Series (2)

Knowledge Base SSG3000X Series (4)

Knowledge Base Spectrum Analysers

Knowledge Base DSA800 Series (70)

Knowledge Base RSA3000 Series (32)

Knowledge Base RSA5000 Series (31)

Knowledge Base SSA3000X Plus Series (2)

Knowledge Base SSA3000X Series (15)

Knowledge Base SSA3000X-R Series (1)

Knowledge Base SVA1000X Series (13)

Knowledge Base Waveform Generators

Knowledge Base DG1000 Series (14)

Knowledge Base DG4000 Series (14)

Knowledge Base SDG1000X Series (10)

Knowledge Base SDG2000X Series (11)

Knowledge Base SDG6000X Series (11)

Knowledge Base SDG800 Series (10)

Product Categories

AC Power Supplies / Frequency Converters
DC Power Supplies
DC Electronic Loads
Test & Measurement
Safety Testers
EMC
Soldering Irons / Test Tools
Manufacturers
Rental
NQA ISO9001 logo

Service & Support

About
Contact
Newsletter
Service Returns Form
Returns Policy
Terms and Conditions
Privacy Policy
Shipping & Delivery
My account
NUWPEC logo

Support, News & Events

Latest News
Future Events
Product Support
Blog
JOSCAR logo

Copyright © 2024. All rights reserved by Telonic Instruments Ltd

Website operated by Jumping Giraffe Ltd. Jumping Giraffe Ltd is not responsible for content on external websites.

CLICK TO CALL

0118 9786911
CLICK TO EMAIL