| Sample Mode | Real-Time Sample Rate |
| Real-Time Sample Rate | Analogue channel:
1 GSa/s (single-channel),
500 MSa/s (dual-channel), 250 MSa/s (three/four-channel)
Digital channel:
1 GSa/s (8-channel), 500 MSa/s (16-channel) |
| Peak Detect | Analogue channel: 4 ns
Digital channel: 4 ns |
| Averaging | After all the channels finish N samples at the same time, N can be 2, 4, 8, 16, 32, 64, 128, 256, 512 or 1024. |
| High Resolution | 12 bit (max.) |
| Interpolation | Sin(x)/x (optional) |
| Minimum Detect Pulse Width | Digital channel: 10 ns |
| Memory Depth | Analogue channel:
24 Mpts (single-channel), 12 Mpts (dual-channel), 6 Mpts (three/four-channel)
Digital channel:
24 Mpts (8-channel), 12 Mpts (16-channel) |
| Input | |
|---|
| Number of Channels | DS1XX4Z Plus/1XX4Z-S Plus: 4 analogue channels, 16 digital channels available after upgrade
DS1054Z: 4 analogue channels |
| Input Coupling | DC, AC or GND |
| Input Impedance | Analogue channel: (1 MΩ±1%) || (15 pF±3 pF)
Digital channel: (100 kΩ±1%) || 8 pF±3 pF) |
| Probe Attenuation Coefficient | Analogue channel: 0.01X to 1000X, in 1-2-5 step |
| Maximum Input Voltage (1MΩ) | Analogue channel:
CAT I 300 Vrms, CAT II 100 Vrms, transient overvoltage 1000 Vpk
Digital channel:
CAT I 40 Vrms, transient overvoltage 800 Vpk |
| Horizontal | |
|---|
| Timebase Scale | 5 ns/div to 50 s/div |
| Maximum Record Length | 24 Mpts |
| Timebase Accuracy | ≤ ± 25 ppm |
| Clock Drift | ≤ ± 5 ppm/year |
| Maximum Delay Range | Negative delay: 1/2 (Memory Depth/Sample Rate)
Positive delay: 1 s to 500 s |
| Timebase Mode | YT, XY, Roll |
| Number of X-Y’s | 1 |
| Waveform Capture Rate | 30,000 wfms/s (dots display) |
| Zero Offset | ±0.5div*minimum time base scale |
| Vertical | |
|---|
| Bandwidth (-3dB) | DS1104Z Plus/1104Z-S Plus: DC to 100 MHz
DS1074Z Plus/1074Z-S Plus: DC to 70 MHz
DS1054Z: DC to 50 MHz |
| Single-shot Bandwidth | DS1104Z Plus/1104Z-S Plus: DC to 100 MHz
DS1074Z Plus/1074Z-S Plus: DC to 70 MHz
DS1054Z: DC to 50 MHz |
| Vertical Resolution | Analogue channel: 8 bits
Digital channel: 1 bit |
Vertical Scale
(Probe ratio is 1X) | 1 mV/div to 10 V/div |
Offset Range
(Probe ratio is 1X) | 1 mV/div to 499 mV/div: ± 2 V
500 mV/div to 10 V/div: ± 100 V |
| Bandwidth Limit | 20 MHz |
Low Frequency Response
(AC coupling, -3dB) | ≤5 Hz (on BNC) |
| Calculated Rise Time | DS1104Z Plus/1104Z-S Plus: 3.5 ns
DS1074Z Plus/1074Z-S Plus: 5 ns
DS1054Z: 7 ns |
| DC Gain Accuracy | <10 mV: ±4% full scale
≥10 mV: ±3% full scale |
| DC Offset Accuracy | ±0.1 div ± 2 mV ± 1% offset |
| Channel to Channel Isolation | DC to maximum bandwidth: >40 dB |
| Trigger | |
|---|
| Trigger Level Range | ±5 div from the centre of the screen |
| Trigger Mode | Auto, Normal, Single |
| Holdoff Range | 16 ns to 10 s |
| High Frequency Rejection | 75 kHz |
| Low Frequency Rejection | 75 kHz |
| Trigger Sensitivity | 1.0 div (below 5 mV or noise rejection is enabled)
0.3 div (above 5 mV and noise rejection is disabled) |
| Edge Type | Rising, Falling, Rising/Falling |
| Pulse Condition | Positive Pulse Width (greater than, lower than, within specified interval)
Negative Pulse Width (greater than, lower than, within specified interval) |
| Pulse Width | 8 ns to 10 s |
| Pulse Width Condition | None, >, <, <> |
| Polarity | Positive, Negative |
| Pulse Width Range | 8 ns to 10 s |
| Windows Type | Rising, Falling, Rising/Falling |
| Trigger Position | Enter, Exit, Time |
| Windows Time | 8 ns to 10 s |
| Edge Type | Rising, Falling |
| Idle Time | 16 ns to 10 s |
| Edge Number | 1 to 65535 |
| Slope Condition | Positive Slope (greater than, lower than, within specified interval)
Negative Slope (greater than, lower than, within specified interval) |
| Time Setting | 8 ns to 10 s |
| Signal Standard | NTSC, PAL/SECAM, 480P, 576P |
| Pattern Setting | H, L, X, Rising, Falling |
| Edge Type | Rising, Falling |
| Delay Type | >, <, <>, >< |
| Delay Time | 8 ns to 10 s |
| Edge Type | Rising, Falling, Rising/Falling |
| TimeOut Value | 16 ns to 10 s |
| Pattern | H, L, X |
| Trigger Condition | >, <, <> |
| Duration Time | 8 ns to 10 s |
| Edge Type | Rising, Falling |
| Data Pattern | H, L |
| Setup Time | 8 ns to 1 s |
| Hold Time | 8 ns to 1 s |
| Polarity | Normal, Invert |
| Trigger Condition | Start, Error, Check Error, Data |
| Baud Rate | 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, 230400 bps, 460800 bps,
921600 bps, 1 Mbps and User |
| Data Bits | 5 bits, 6 bits, 7 bits, 8 bits |
| Trigger Condition | Start, Restart, Stop, Missing Ack, Address, Data, A&D |
| Address Bits | 7 bits, 8 bits, 10 bits |
| Address Range | 0 to 127, 0 to 255, 0 to 1023 |
| Byte Length | 1 to 5 |
| Trigger Condition | Timeout, CS |
| Timeout Value | 16 ns to 10 s |
| Data Bits | 4 bit to 32 bit |
| Data Line Setting | H, L, X |
| Measure | |
|---|
| Cursor | Manual mode:
Voltage deviation between cursors ( △V )
Time deviation between cursors ( △T )
Reciprocal of △T (Hz) (1/ △T )
Track mode:
Voltage and time values of the waveform point
Auto mode:
Allow to display cursors during auto measurement |
| Auto Measurement | Analogue channel:
Period, Frequency, Rise Time, Fall Time, Positive Pulse Width, Negative Pulse Width, Positive Duty Cycle,
Negative Duty Cycle, tVmax, tVmin, Positive Rate, Negative Rate, Delay 1→2 , Delay 1→2 , Phase
1→2 , Phase 1→2 , Maximum, Minimum, Peak-Peak Value, Top Value, Bottom Value, Amplitude, Upper
Value, Middle Value, Lower Value, Average, Vrms, Overshoot, Pre-shoot, Area, Period Area, Period Vrms,
Variance
Digital channel:
Period, Frequency, Positive Pulse Width, Negative Pulse Width, Positive Duty Cycle, Negative Duty Cycle,
Delay 1→2 , Delay 1→2 , Phase 1→2 , Phase 1→2 |
| Number of Measurements | Display 5 measurements at the same time |
| Measurement Range | Screen or cursor |
| Measurement Statistic | Average, Max, Min, Standard Deviation, Number of Measurements |
| Counter | Hardware 6 bits counter (channels are selectable) |
| Display | |
|---|
| Display Type | 7.0 inch TFT LCD display |
| Display Resolution | 800 horizontal × RGB × 480 vertical pixel |
| Display Colour | 16 million color (24 bit true color) |
| Persistence Time | Min, 100 ms, 200 ms, 500 ms, 1 s, 5 s, 10 s, Infinite |
| Display Type | Dots, Vectors |
| I/O | |
|---|
| Standard Ports | USB Host, USB Device, LAN, AUX Output (TrigOut/PassFail) |
| General Specifications | |
|---|
| Output Voltage | About 3 V, peak-peak |
| Frequency | 1 kHz |
| Power Voltage | 100 V to 240 V, 45 Hz to 440 Hz |
| Power | Maximum 50 W |
| Fuse | 2 A, T degree, 250 V |
| Temperature Range | Operating: 0℃ to +50℃
Non-operating: -40℃ to +70℃ |
| Cooling Method | Fan cooling |
| Humidity Range | 0℃ to +30℃ : ≤95℃ relative humidity,
+30℃ to +40℃ : ≤75℃ relative humidity,
+40℃ to +50℃ : ≤45℃ relative humidity |
| Altitude | Operating: under 3,000 meters,
Non-operating: under 15,000 meters |
| Dimensions | Width × Height × Depth = 313.1 mm × 160.8 mm × 122.4 mm |
| Weight | Without package 3.2 kg ± 0.2 kg,
With package 3.8 kg ± 0.5 kg |
| Calibration Interval | The recommended calibration interval is 18 months. |
Rigol DS1202Z-E Datasheet
michaelsmith538 (verified owner) –
Bought this scope after seeing a review on YouTube. Just stating my journey into electronics ( so I’m still learning ) just would like to say the Guys at Telonic were great, ordered at 2:45 and it was delivered the next day, great service. I’m now looking to purchase a signal generator next so will be using Telonic
David M –
Product delivered next working day, as promised. First class service when I contacted Customer Service team Excellent service all round. Product works well
Anonymous –
Ordered at weekend, package dispatched early the next working week and arrived next day from dispatch. Have been used to an analogue scope before this so still getting used to the menus on the device but seems to work very well.
Paul S –
Equipment was delivered promptly and is physically pretty much as described on the website. Only really calibrated the probes at the time of writing but the screen looks clear and the basic knobs and buttons are intuitive.
They lost a star on the paper work. I did find the user guide on the website but it seems to have been translated by different people. In some areas the English is fine and in others its clearly written in Chinglish.
The offer on the website included free software. Not clear what software is being provided or if its has been provided. I haven’t quite got that far in the user manual yet.
Anonymous –
Excellent scope, delivered promptly.
Peter M –
I called this company before placing an order – they were extremely helpful. Nothing else in the UK to compare as far as I could see and when I placed an order it was dispatched immediately – Great Service!!!
Keith R –
I needed a cheap scope to replace my ageing Tek 465
The Rigol is easy to use has tons of features and takes up a lot less room that the Tek.
It does all I need it to do and more.
For the money, I can’t really fault it.