| Sampling Modes |
Real-Time |
| Sampling Rate |
1GSa/s, 200MSa/s |
| Averages |
N time acquisitions, all channels simultaneously, N is selectable from 2, 4, 8, 16, 32, 64, 128 and 256. |
| Input |
|
| Input Coupling |
DC, AC, GND |
| Input Impedance |
1MΩ± 2%, in parallel with 15pF± 3pF |
| Probe Attenuation Factors |
1X, 5X, 10X, 50X, 100X, 500X,1000X |
| Maximum Input Voltage |
400V (DC＋AC Peak, 1MΩ input impedance)
40V (DC+AC Peak) |
| Time Delay Between Channel (typical) |
500ps |
| Horizontal |
|
| Sample Rate Range |
Real-Time: 13.65Sa/s-1GSa/s
Equivalent: 13.65Sa/s-25GSa/s |
| Waveform Interpolation |
Sin(x)/x |
| Scan Speed Range |
2ns/div~50s/div, DS1102X
5ns/div~50s/div, DS1052X
1-2-5 Sequence |
| Sample Rate and Delay Time |
± 50ppm (over any 1ms time interval) |
| Delta Time Measurement Accuracy (Full Bandwidth) |
Single-shot: ± (1 sample interval + 50ppm × reading + 0.6 ns)
>16 averages: ± (1sample interval + 50ppm × reading + 0.4 ns) |
| Vertical |
|
| A/D Converter |
8-bit resolution, each channel samples simultaneously[2] |
| Volts/div Range |
2mV/div~10V/div at input BNC |
| Maximum Input |
Analog channel maximum input voltage
CAT I 300Vrms, 1000Vpk；instantaneous voltage 1000Vpk CAT II 100Vrms，1000Vpk
RP2200 10:1：CAT II 300Vrms RP3200 10:1：CAT II 300Vrms RP3300 10:1：CAT II 300Vrms |
| Offset Range |
± 40V(200mV-10V), ± 2V(2mV-100mV) |
| Analogue Bandwidth |
100MHz (DS1102D,DS1102E)
50MHz (DS1052D, DS1052E) |
| Single-shot Bandwidth |
80MHz (DS1102D, DS1102E)
50MHz (DS1052D, DS1052E) |
| Selectable Analog Bandwidth Limit (typical) |
20MHz |
| Lower Frequency Limit (AC –3dB) |
≤5Hz (at input BNC) |
| Rise Time at BNC, typical |
<3.5ns, <7ns,
On (100M, 50M) respectively |
| DC Gain Accuracy |
2mV/div-5mV/div:
± 4% (Sample or Average acquisition mode) 10mV/div-10V/div:
± 3% (Sample or Average acquisition mode) |
| DC Measurement Accuracy, Average Acquisition Mode |
Average of ≥16 Waveforms with vertical position at zero: ± (DC Gain Accuracy× reading+0.1div+1mV)
Average of ≥16 Waveforms with vertical position not at zero: ±[DC Gain Accuracy× (reading+vertical position)+(1% of vertical position) + 0.2div]
Add 2mV for settings from 2mV/div to 200 mV/div |
| Delta Volts Measurement Accuracy (Average Acquisition Mode) |
Delta Volts between any two averages of 16 waveforms acquired under same setup and ambient
conditions: ± (DC Gain Accuracy× reading + 0.05 div) |
| Trigger |
|
| Trigger Sensitivity |
0.1div~1.0div (adjustable) |
| Trigger Level Range |
Internal: ± 5 divisions from center of screen
External: ± 1.2V |
| Trigger Level Accuracy (typical) applicable for the signal of rising and falling time ≥20ns |
Internal: ± (0.3div × V/div)(± 4 divisions from center of screen)
External: ± (6% of setting + 200 mV) |
| Trigger Offset |
Normal mode: pre-trigger (262144/ sampling rate), delayed trigger 1s
Slow Scan mode: pre-trigger 6div, delayed trigger 6div |
| Trigger Holdoff range |
100ns~1.5s |
| Set Level to 50% (Typical) |
Input signal frequency ≥50Hz |
| Edge trigger slope |
Rising, Falling, Rising + Falling |
| Trigger condition |
(＞, ＜, =) Positive pulse, (＞, ＜, =) negative pulse |
| Pulse Width range |
20ns ~10s |
| Video standard & line frequency |
Support standard NTSC, PAL and SECAM broadcast systems. Line number range: 1~525 (NTSC) and 1~625 (PAL/SECAM) |
| Trigger condition |
(＞, ＜, =) Positive slope, (＞, ＜, =) negative slope |
| Time setting |
20ns~10s |
| Trigger on CH1 |
Edge, Pulse, Video, Slope |
| Trigger on CH2 |
Edge, Pulse, Video, Slope |
| Trigger mode |
D0~D15 select H, L, X, , |
| Trigger Type |
D0~D15 select H, L, X |
| Qualifier |
＞, ＜, = |
| Time setup |
20ns~10s |
| Measure |
|
| Cursor |
Manual mode:
Voltage difference between cursors (∆V) Time difference between cursors (∆T) Reciprocal of ∆T in Hertz (1/∆T)Track: Voltage value for Y-axis waveform Time value for X-axis waveformAuto: Cursors are visible for Automatic Measurement |
| Auto Measurement |
Vpp, Vamp, Vmax, Vmin, Vtop, Vbase, Vavg, Vrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Time, +Width, -Width, +Duty, -Duty, Delay1→2 , Delay1→2 |
| Display |
|
| Display Type |
5.7 in. (145 mm) diagonal TFT Liquid Crystal Display |
| Display Resolution |
320 horizontal × RGB× 234 vertical pixels |
| Display Colour |
64K color |
| Display Contrast (typical) |
150:1 |
| Backlight Brightness (typical) |
300 nit |
| I/O |
|
| Standard Ports |
USB Host, USB Device, LAN, AUX Output (TrigOut/PassFail) |
| General Specifications |
|
| Supply Voltage |
100 ~ 240 VACRMS, 45~440Hz, CAT II |
| Power Consumption |
Less than 50W |
| Fuse |
2A, T rating, 250 V |
| Ambient Temperature |
Operating 10℃~ 40℃, Non-operating -20℃~ +60℃ |
| Cooling Method |
Fan force air flow |
| Humidity |
+35℃ or below: ≤90% relative humidity, +35℃~ +40℃: ≤60% relative humidity |
| Altitude |
Operating 3,000 m or below, Non-operating 15,000 m or below |
| Size |
W: 303mm, H: 154mm, D: 133mm |
| Weight |
Without Package: 2.4kg, Packaged: 3.8 kg |
| Calibration Interval |
The recommended calibration interval is one year |
Rigol DS1000E Datasheet
Michael H –
.